ST Front Rack
Assembly Instructions
Treker 4200/4400 ST, 4210/4410 ST & 4220/4420 ST Models
Manual No. 701-123M
Before You Start
General Information
These assembly instructions apply to the following
ST Front Rack Accessories listed below:
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
701-171A
701-122A
701-053A
701-126A
Series 20 ST Treker Front Rack Kit:
Mounts to the Heavy Duty Brush Guard
Series 00 & 10 ST Front Rack Kit:
Mounts to the Heavy Duty Brush Guard
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
Series 00 & 10 ST Front Rack Kit:
Mounts to the Standard Brush Guard
ST Front Rack Adapter Kit:
Attaches Front Rack to a Heavy Duty
Brush Guard
Your Land Pride Front Rack is exclusively designed for
your ST Treker. Please read these instructions and your
vehicle Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).
Tools required:
• Safety glasses
• Work gloves
• Two 1/2" box end or open end wrenches
• Phillips screwdriver
Assembly Instructions
A separate Parts Manual for replacement parts can be
purchased from your dealer or available free of charge at
handy when placing an order.
A detailed listing of parts for each accessory kit is
provided on page 5. Use the list for your particular
application as a checklist to inventory parts received.
Please contact your local Land Pride dealer for any
missing hardware.
Manual Part Numbers:
• Operator’s Manual (20 ST Series) . . . . . . . 700-504M
• Operator’s Manual (00 & 10 ST Series). . . 700-108M
• Parts Manual (20 ST Series) . . . . . . . . . . . 700-504P
• Parts Manual (10 ST Series) . . . . . . . . . . . 700-109P
• Parts Manual (00 NT/ST Series) . . . . . . . . 700-108P
Initial Preparations
Before servicing the vehicle the following procedure must
be met to secure the vehicle:
1. Park vehicle on a level surface. Don’t work under or
Further Assistance
around a vehicle parked on an incline.
2. Make the following gear and park brake selections:
a. 10 & 20 ST Series Trekers:
Your dealer wants you to be satisfied with your new Front
Rack. If for any reason you do not understand any part of
this manual or are not satisfied with the service received,
the following actions are suggested:
• Set shift selector in Park.
b. 00 ST Series Trekers:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
• Set shift selector in forward gear.
• Set park brake.
3. Turn ignition switch off and remove switch key.
4. Chock front and back of a wheel to prevent vehicle
from rolling.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
5. Go to one of the installation kits listed below to
complete installation.
3. For further assistance write to:
• For installation of Kit No. 701-171A, see page 2.
• For installation of Kit No. 701-122A, see page 3.
• For installation of Kit No. 701-053A, see page 4.
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
• For installation of Kit No. 701-126A,
see page 2 or page 3.
© Copyright 2007
Printed
2/23/07
1
Land Pride
Assembly Instructions
23706
Front Rack Assembly To Heavy Duty Brush Guard
Series 00 & 10 ST Trekers
Figure 2
Assembly Instructions for
Kit No’s. 701-122A and 701-126A
Front Rack mounted to Heavy Duty Brush
Guard (Reference Series 00 &10 ST Trekers)
4. Attach back two tabs on Front Rack (#2) to the four
post accessory bar (#1) with 1-1/2" U-Clamps (#3),
5/16" x 2" Carriage Bolts (#7), and 1 1/8" long
Spacers (#4), Secure with 5/16" hex lock nuts (#9).
Do not tighten.
Refer to Figure 2:
1. Remove plastic end caps (#11) from the Heavy Duty
Brush Guard (#6).
5. Adjust Front Rack (#2) to be level and centered on
the Treker.
2. Attach adapter bracket (#5) to Heavy Duty Brush
Guard with 5-16"-18 x 3/4" lg. GR5 hex bolts (#8) and
5/16" hex locknuts (#10). Do not tighten.
6. Tighten all 5/16" hex lock nuts (#9 & #10) to 17 ft. lbs
of torque.
3. Align front two tabs on the Front Rack (#2) with holes
in the adapter bracket (#5) as shown. Insert two
5/16"-18 x 1-1/2 GR5 Bolts (#8) through the Front
Rack and adapter bracket. Secure with 5/16" hex
lock nuts (#10). Do not tighten.
7. Replace plastic end caps (#11).
2/23/07
■
Manual No. 701-123M
3
Land Pride
Assembly Instructions
23719
Front Rack Assembly To Standard Brush Guard
Series 00 & 10 ST Trekers
Figure 3
Assembly Instructions for
Kit No. 701-053A
2. Attach back two tabs on Front Rack (#2) to the four
post accessory bar with two 1-1/2" U-Clamps (#4),
5/16" -18 x 2" lg. carriage bolts (#8), and 1 1/8" long
spacers (#5), secure with 5/16" hex lock nuts (#9).
Do not tighten.
Front Rack mounted to Standard Brush
Guard (Reference Series 00 &10 ST Trekers)
Refer to Figure 3:
1. Align front two tabs on the Front Rack (#2) with top
two tabs on the Standard Brush Guard (#6). Insert
two 5/16"-18 x 1-1/2 GR5 Bolts (#7) through tabs in
Front Rack (#2), 5/8" long spacers (#3) and tabs in
Brush Guard (#6). Secure with 5/16" hex lock nuts
(#10). Do not tighten.
3. Adjust the Front Rack (#2) to be level and centered
on the Treker.
4. Tighten all 5/16" hex lock nuts (#9 & #10) to 17 ft. lbs
of torque.
Manual No. 701-123M
2/23/07
4
Land Pride
Assembly Instructions
Kit No. 701-171A
Series 20 ST Front Rack Kit:
Mounts to the Heavy Duty Brush Guard
Qty.
Part No.
Part Description
1
1
840-326C
701-126A
RACK, ST FRONT CARGO
ST FRONT RACK ADAPTER KIT (SEE KIT NO. 701-126A BELOW FOR LISTING OF PARTS)
Kit No. 701-122A
Series 00 & 10 ST Front Rack Kit:
Mounts to the Heavy Duty Brush Guard
Qty.
Part No.
Part Description
1
1
701-053A
701-126A
ST FRONT RACK KIT (SEE KIT NO. 701-053A BELOW FOR LISTING OF PARTS)
ST FRONT RACK ADAPTER KIT (SEE KIT NO. 701-126A BELOW FOR LISTING OF PARTS)
Kit No. 701-053A
Series 00 & 10 ST Front Rack Kit:
Mounts to the Standard Brush Guard
Qty.
Part No.
Part Description
1
2
2
4
2
2
2
1
FRONT RACK ST
HHCS 5/16-18X1 1/2 GR5
RHSNB 5/16-18X2 GR5
NUT HEX NYLOCK 5/16-18 PLT
5/8 U-CLAMP SPACER UCS58BLK
1 1/2" U-CLAMP UC112
1 1/8 U-CLAMP SPACER 10458
MANUAL, ST FRONT CARGO RACK
802-012C
802-199C
803-084C
700-361D
700-362D
700-363D
701-123M
Kit No. 701-126A
ST Front Rack Adapter Kit:
Attaches Front Rack to a Heavy Duty Brush Guard
Qty.
Part No.
Part Description
1
1
4
4
700-459D
701-123M
802-387C
803-177C
RACK MOUNT FRONT PLATE
MANUAL, ST FRONT CARGO RACK
HEX FLANGE SCREW 5/16-18X3/4 GR5
HEX NUT FLANGE TOP LOCK 5/16-18
2/23/07
Manual No. 701-123M
5
|