Technical Bulletin
Date: September 2005
Type
Policy Letter
√ Service Information
No:
TDL-0050B-B
ITDL-0020A-B
Page 1 of 4
Attention
Service Managers
Supersedes TDL-0050A-B
ITDL-0020-B
√ Service and Parts Managers
Models
AAV1200AGW, AAV1200AJW, AAV1200AKW, AAV1200ARW,
AAV1200AWW, AAV2200AGW, AAV2200AJW, AAV4200AGW,
ALW221RJW,CAV1000AWW, CAV2000AGW, CAV2000AJW,
CAV2000AKW, CAV2000AWQ, CAV2000AWW, CAV4000AWW,
CW5000W, CW6000Q, CW6000W, CW7500Q, CW7500W, DLW231RAW,
HAV1200ARW, HAV1200AWQ, HAV1200AWW, HAV2360AWW,
HAV2460AWW, HAV2557AWW, HAV2558AWW, HAV3460AWW,
HAV4200AKW, HAV4200ATW, HAV4200AWW, HAV4657AWW,
JAV4200AWQ, LNC6760B71, LNC6762B01, LNC6762B71, LNC6764A71,
LNC6766B71, MAV2200AJW, NAV3200AWW, NAV4200AGW,
NAV4200AKW, PAV1200AWW, PAV2200AAW, PAV2200AGW,
PAV2300AGW, PAV2300AWW,PAV2360AWW, PAV3200AAW,
PAV3200AGW, PAV3240AWW, PAV3300AGW,PAV3300AKW,
PAV3300AWW, PAV3360AWW, PAV4960AWW, PAV5000AWQ,
PAV5000AWW, PAV5057AWW, PAV5058AWW, PAV5157AWW,
PAV5158AWW, PAVT234AWW, PAVT244AWW, PAVT344AWW,
PAVT444AWW
Brand
Admiral
Amana
Crosley
Jenn-Air
Magic Chef
Maytag
Maytag Performa
Product
Laundry
Issue
Wash basket leans to one side, generally to the right as you face the washer
during spin cycle.
Warranty
Action
Standard product manufacturing warranty applies.
Replace original base with Kit 12002701. The replacement of the base, new snubber,
and six springs (included in the Kit) will reduce tub lean to an acceptable level.
NOTE: Some tub lean is normal.
1. Disconnect power supply to unit.
2. Tilt washer and remove belt from underside of base.
3. Remove back cover to access and remove drain hose clamps.
NOTE: There will be water remaining in the hose from the last cycle.
© 2005 Maytag Services
7. Remove pressure switch hose from outer tub. Remove screws from sides and rear of unit around bottom,
connecting cabinet to base. Remove cabinet from base and set aside. Be sure to lay down a protective pad
before removing tub and transmission assembly from base. Remove tub springs using the spring removal
tool; be careful not to let tub and transmission assembly tip over.
8. Be sure to lay down a protective pad before removing tub and transmission assembly from base. Remove
tub and transmission assembly, turn over and lay on protective pad.
9. Remove dust cap, retaining ring, washer, cam, and pulley from bottom of transmission.
Pulley
Cam
Retaining ring
Washer
Dust cap
10. Remove stator from transmission using Brake Removal Tool 12002012, refer to Service Manual for
disassembly procedures. Remove old snubber from transmission.
11. Be sure to wash hands to remove any dirt or grease before handling new snubber. Clean new snubber with
alcohol before installing. Install new snubber. Insure snubber is centered.
Snubber
TDL-0050B-B
ITDL-0020A-B
© 2005 Maytag Services
Page 3 of 4
9/30/2005
12. Reinstall stator by locating the dimple on the stator, and tightening the screw next to the dimple first. Next
tighten the screw 180 degrees across from the dimple. Install and tighten remaining screws. Reinstall pulley,
cam, washer, retaining ring, and dust cap.
Dimple
Stater
13. Turn new base upside down and apply grease at bottom of the spring hole pockets to eliminate noise
between spring and base interaction.
Apply grease at bottom of
spring hole pockets.
14. Clean the dome area of new base with alcohol then apply corn starch.
Apply corn starch to new base
on dome area after cleaning
with alcohol.
15. Reinstall motor and pump to new base.
16. Transfer transmission and outer tub onto new base. Use spring tool 22002922 to avoid over stretching the
springs.
17. Transfer cabinet shell onto new base and reassemble washer. Be sure to reattach pressure switch hose to
back of tub, drain pump hoses with clamps to drain pump, and wire harness to motor. Check all hoses and
wires to make sure they are secure.
18. Test washer.
Page 4 of 4
9/30/2005
© 2005 Maytag Services
TDL-0050B-B
ITDL-0020A-B
|