De’Longhi Appliances
via Seitz, 47
31100 Treviso Italia
C
C1
C4
C2 CLEAN
C3
C5
D
D2
D3
D4
D5
D6
D1
D7
D8
D9
D10
2
A
A1
A14
B
A2
A5
A6
A3
A4
A7
A13
A12
A11
A8
A10
A9
B2
B4
B6
B8
B
B1
B3
B5
B7
B9
B10
B12
B11
3
17 OZ /
0.5 L
1
2
3
4
5
9
6
7
8
1
10
11
2
12
13
14
15
16
17
18
19
20
21
4
CLEAN
23
24
28
25
22
27
26
29
30
32
31
5
Safety warnings
Symbols used in these instructions
The important recommendations have these symbols. These
warnings must be followed.
Attention:
Keep the packaging material (plastic bags, expanded
polystyrene) out of the reach of children.
Danger!
Attention:
Failure to comply can be or is the cause of injury due to life-
Do not allow the appliance to be used by persons (including
children)withreducedpsycho-physical-sensorialcapacitiesor
that have insufficient experience and knowledge, unless they
are carefully monitored and trained by a person responsible
for their safety. Watch children, do not let them play with the
appliance.
threatening electric shocks.
Attention!
Failure to comply can be or is cause of injury or damage to the
appliance.
Scalding hazard!
Failure to comply can be or is the cause of scalding or burns.
Scalding hazard!
This appliance produces hot water and steam may form
during operation.
Pay attention not to come into contact with hot water sprays
or steam.
Please note:
This symbol highlights recommendations and important
information for the user.
Fundamental warnings regarding safety
Donottouchthecupholderwhentheapplianceisonbecause
it can get.
Danger!
As the appliance operates using electric current, electric
Complying with intended use
shocks can not be excluded.
Therefore, follow the safety recommendations given:
This appliance is manufactured for the preparation of coffee
and to heat beverages.
•
Donottouchtheappliancewhenyouhavewethandsor
feet.
This appliance is intended exclusively for domestic use. It is
not intended for the use in:
•
•
Do not touch the plug with wet hands.
Make sure that the socket used can always be easily
reached, so that the plug can be removed when
required.
Remove the plug from the socket by pulling directly on
theplugitself. Donotpullthecableasdamagecouldbe
caused.
Remove the plug from the socket to disconnect the
appliance completely.
Do not attempt to repair the appliance if it should
breakdown.
•
rooms used as kitchens for personnel in shops, offices
and other work areas
farm holidays
hotels, motels and other reception structures
guest houses
•
•
•
•
Any other use must be considered improper and therefore
dangerous. The manufacturer is not liable for damage
deriving from improper use of the appliance.
•
•
Switch the appliance off, remove the plug from the
socket and contact the After-Sales Technical Assistance.
If the plug or power supply cable are damaged, have
them replaced exclusively by the De’Longhi After-Sales
Service, in order to avoid risks
•
•
•
Duringcleaning,neverimmersethemachineinwater:it
is an electric appliance.
Before performing any cleaning operations to the
external parts of the appliance, switch the machine off,
remove the plug from the socket and let the machine
cool down.
6
Functioning lights
en
Lights
Operation
Meaning of lights
Turn on from general ON/OFF switch, at The appliance performs a self-test,
the back of the appliance.
signalled by the sequential flashing of
lights.
The appliance is on: no accessory is
connected to coupling A2.
The appliance is heating up to make
coffee: when the 1 or 2 cup lights stop
flashing, the appliance has reached the
ideal temperature to deliver coffee.
The appliance is on: the hot water spout The appliance is heating up to make
D7 is connected to coupling A2.
coffee or to deliver hot water: when the
1 or 2 cup lights and the hot water spout
light stop flashing, the appliance has
reached the ideal temperature to deliver
coffee or hot water.
The appliance is on: the milk container C The appliance is heating up to make
is connected to coupling A2.
coffee, cappuccino or latte macchiato:
when the 1 or 2 cup lights, the
cappuccino and latte macchiato lights
stop flashing, the appliance has reached
ideal temperature to deliver coffee or
cappuccino or latte macchiato.
The appliance has been unused for 75
minutes for the ON/STAND-BY button
has been pressed.
The appliance is in STAND-BY: to switch it
back on, press the
button.
The time interval before stand-by is
adjustable: see section “Adjust Stand-by
interval”.
The water tank is empty or the appliance See section “ Troubleshooting.”(page
cannot deliver. 15).
7
Description
en
Description of appliance
(page 3 - A )
D7. Removable water/steam spout
D8. Reactive strip to detect water hardness
(Total hardness test)
A1. Cup holder/Warming plate
A2. Water spout/milk container coupling
A3. General ON/OFF switch
A4. Power supply cable socket
A5. Boiler outlet/Infusion assembly
A6. Water tank seat
A7. Water tank lid
A8. Water tank with seat for water filter
A9. Water refill indicator
D9. Descaler
D10. Water softener filter
Instructions for use
Read these instructions carefully before using the appliance.
Failure to respect these instructions may result in personal
injury or damage to the appliance.
The manufacturer is not liable for damage as a result of failure
to comply with these user instructions.
A10. Drip tray
A11. Indicator for drip tray maximum water level
A12. Cup tray
A13. Sliding tray for long coffee/latte macchiato glass
A14. Cup warmer button
Please note:
Keep these instructions. If the appliance should be transferred
to other persons, these instructions must accompany it.
Checking the appliance
Description of control panel (B)
(page 3 - B)
B1. ON/Stand-by Button
B2. ON/Stand-by Light
B3. 1 cup button
B4. 1 cup /“temperature OK”light
B5. 2 cups button
B6. 2 cups/“temperature OK”light
B7. Hot water button
After the packaging has been removed, check the integrity of
the appliance and the presence of all accessories. Do not use
the appliance if it is visibly damaged. Contact the Customer
Experience.
Installing the appliance
Attention!
The following safety measures must be complied with when
installing the appliance:
B8. Hot water light
•
•
The appliance could be damaged by water infiltration.
Do not position the appliance near water faucets or sinks.
The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the
temperature can fall below freezing point.
Positionthepowersupplycableinawaythatitcannotbe
damaged by sharp edges or by contact with hot surfaces
(e.g. electric stoves, cooking surfaces, or gas burners).
B9. Hot milk/cappuccino button
B10. Hot milk/cappuccino/“temperature OK”light
B11. Hot milk/latte macchiato button
B12. Hot milk/latte macchiato/“temperature OK”light
Milk container description
(page 2 - C)
C1. Milk frother lid with froth regulator
C2. CLEAN button
•
C3. Milk SpoutTube
Connecting the appliance
C4. Milk intake tube
C5. Milk container
Attention!
Make sure that the electric mains voltage corresponds with
that indicated on the data plate on the base of the appliance.
Insert the power supply cable connector in the socket on the
backof the appliance (fig. 1); then insertthe plug in the power
outlet. Check that the mains power supply voltage corresponds
to the value indicated on the rating plate on the bottom of the
appliance. If the power socket does not match the plug on the
appliance, have the socket replaced with a suitable type by a
qualified professional.
Description of accessories
(page 2 - D)
D1. Filter-holder cup
D2. 1 coffee crema filter
D3. 2 coffee crema filter
D4. ESE pod crema filter
D5. Power supply cable (removable)
D6. Tamper/dispenser measure
8
Instructions for use
en
Activation of the water filter and filling of the water
tank
programming menu, press button
again.
Setting the temperature
•
Remove the filter from the packaging and rinse it with
about 17 OZ / 0.5 L of running water (fig. 2).
Turn the calendar disc (see fig. 3) until the following 2
months of use are displayed.
To modify the temperature (low, medium, high) of the water
used to make the coffee, proceed as follows:
1. Access the programming menu;
•
2. Keep button
pressed until the lights relative to the
Please note
wanted temperature turn-on (see chart below).
the filter has a two month duration if the appliance is used
normally, whereas if the machine remains unused with the
filter installed, it has a maximum 3 month duration.
3. When the lights relative to the wanted temperature turn-
on, release the button.
4. Press
to turn the appliance off (stand-by).
•
•
•
•
Remove the water tank and fill it with fresh water (do not
exceed the MAX line) (fig. 4).
Completely dip the filter in the water, tilting it to enable
air bubbles to come out (fig. 5).
Insertthefilterintheappropriateseat(fig.6),pressdown
and close the tank with the lid.
Place the tank back into the machine (Ensure the water
level is not over the MAX line) (fig. 7).
Adjust Stand-by
The machine is pre-set to switch to stand-by after 75 minutes
of non-use. This time interval can be modified so that the
appliance switches off after 15 minutes or after 3 hours.
Proceed as follows:
1. Access the programming menu;
2. Keep the
button pressed until the lights relative to
The filter is now activated and the machine can be used.
the desired stand-by interval turn-on(see chart below).
3. When the lights relative to the wanted stand-by interval
turn-on, release the button.
Appliance first use
•
Turn the appliance on by pressing the I/O main switch
A3 at rear in pos. I: the appliance performs a self-test,
signalled by the sequential flashing of the lights.
Once the self-test is completed, the“hot water spout”light
B8 flashes while the others turn-off: the appliance signals
it is necessary to insert the hot water spout (fig. 8).
Place a container underneath the spout with minimum
capacity of 100 ml (fig. 9).
4. Press
to turn the appliance off (stand-by).
•
“Setting temperature” and “Adjust Stand-by” chart
Temperature
Corresponding lights Stand-by after
15 minutes
•
•
•
Low
Press the “hot water”button
: delivery starts and
interrupts automatically.
Medium
High
75 minutes
3 hours
The coffee and water spout lights flash to indicate the
appliance is reaching temperature: when the lights stop
flashing and remain permanently on, the appliance is
ready for use.
Please note: upon first use
•
•
If lights
again.
and
flash, press the
button
Upon first use, it is necessary to make 4-5 coffees or
4-5 cappuccinos before the machine gives a satisfying
results.
Set the water hardness
The lights signaling the need to descale the appliance, after
a pre-set period of operation depends on the hardness of the
water. It is possible to program the machine according to the
actual water hardness in use in the area, thus making descaling
less frequent. Proceed as follows:
Settings of the programming menu
To access the programming menu, ensure the appliance is
in stand-by, simultaneously press buttons
and
until the ON/Stand-by (B2) light flashes: the appliance is in
programming mode. Set the machine as wanted; to exit the
1. Remove the provided reactive strip “TOTAL HARDNESS
TEST”from its packaging.
9
Instructions for use
en
•
To prepare one coffee, fill the filter with one level
measuring spoon of ground coffee, about 0.24 oz./7 gr
(fig. 11). If you wish to prepare two cups of coffee, fill
the filter with two less-than-level measuring spoons
of ground coffee (about 0.48 oz./7+7 gr.). Fill the filter
a little at a time to prevent the ground coffee from
overflowing.
2. Completely dip the strip into a glass of water for one
second.
3. Remove the strip from the water and shake it slightly.
After about one minute 1, 2, 3 or 4 red squares form,
depending on the hardness of the water (4 red squares =
very hard water).
4. Access the programming menu.
5. Once obtained the result of the strip, keep the“hot water”
button pressed until the lights turn-on, as in
following table:
Attention:
For correct use, before filling the filter with ground coffee
always make sure there is no residual coffee from the previous
infusion in the filter.
•
Distribute the ground coffee evenly and press it lightly
using the coffee tamper (fig. 12). Pressing the ground
coffee is very important to obtain a good espresso. If
excessively pressed, the coffee will slowly leak and it will
be stronger. Whereas, if slightly pressed, the coffee will
come out too quickly and will be light.
•
Removeanyexcesscoffeefromtherimofthefilter-holder
and attach it to the machine: for correct attachment,
align the filter-holder handle to symbol
OPEN (fig.
13), attach the filter-holder and turn handle to the right,
until aligned to position CLOSE (fig. 14).
•
•
Position the cup or cups under the filter-holder spouts
(fig. 15). It is advised to heat the cups before making the
coffee, rinsing them with hot water.
Ensure the lights relative to the coffee buttons are on,
press the coffee buttons (
or
): the appliance
proceeds and interrupts automatically.
5. When the lights relative to the detected water hardness
turn-on, release the button.
How to prepare espresso using pods
6. Press
button to turn the appliance off (stand-by).
Please note:
use pods that comply with the ESE Standard: this will be
indicated on the packaging by the following mark.
Please note:
If the water filter is correctly used, set the machine on to a
lower hardness level compared to that detected by the reactive
strip.
The ESE Standard is a system accepted by
leading coffee pod manufacturers and allows
espresso coffee to be made simply and
without mess.
ON/OFF and stand-by
Whenthemainswitchisinpos. I, turntheapplianceonandoff
(stand-by) by pressing the
button.
•
•
Insert the filter for pods coffee (D4
holder (fig. 10).
) in the filter-
The appliance automatically turns off (stand-by) after 75
minutes of non-use: to change the non-use time, refer to
paragraph “Adjust stand-by”.
Insert the pod, centering it as close as possible on the
filter (fig. 16). Always follow the instructions of the pod
pack for correct positioning of the pod in the filter.
Attach the filter-holder to the machine: for correct
attachment, alignthefilter-holderhandletosymbol
OPEN (fig. 13), attach the filter-holder and turn handle to
the right, until aligned to position CLOSE (fig. 14).
How to prepare espresso using ground coffee
•
•
Insert the filter for ground coffee (D2 or D3) in the filter-
holder (fig. 10). Use the filter
one coffee or the filter
coffees.
if wanting to make
if wanting to make 2
10
Instructions for use
exceedingthemaximumof0.5l(fig. 18). Rememberthat
every notch on the side of the container corresponds to
100 ml of milk.
en
•
•
Position the cup under the filter-holder spouts. It is
advised to heat the cup before making the coffee, rinsing
it with hot water.
Ensure the lights relative to the coffee buttons are on,
Please note!
press the coffee button
:
the appliance proceeds
•
For a more dense and homogenous froth, It is
recommendedtouseskimmilkatrefrigeratortemperature
(about 41° F / 5° C).
and interrupts automatically.
Please note:
•
•
•
While the machine is preparing the coffee, it can be
stopped at any time by pressing the previously pressed
coffee button.
Once delivery is completed, if you would like to to increase
the amount of coffee inside the cup, keep the previously
pressed coffee button pressed (within 3 seconds) of delivery.
Turn the handle from right to left to release the filter-
holder.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 19).
4. Place the lid on the milk container.
5. Remove the hot water spout from the nozzle by pushing
the button (fig. 20).
6. Attach by inserting the container to the nozzle (fig. 21).
7. Set-up the machine to make coffee (see “how to prepare
espresso”pg. 10).
8. Place the cup for cappuccino or the glass for Latte
Macchiato under the coffee spout and adjust the milk
spout (fig. 22). If using tall cups or glasses, reposition the
cup-holder, as shown in fig. 23).
Scalding hazard!
To avoid sprays, never release the filter-holder while the
machine is delivering and wait a few seconds after delivery.
9. Vary the froth regulator depending on the amount of
froth wanted and type of milk used (fig. 24).
Program the amount of coffee in the cup
The machine has been set by default to deliver standard
amounts of coffee. If you would like to amend to amend these
quantities, proceed as follows:
To prepare the Cappuccino: press button
.
To prepare the latte macchiato: press button
.
1. Place a cup under the coffee spout.
9. After having delivered the frothed milk, the machine
automatically prepares the coffee.
2. Keep the button to be programmed (
pressed. The machine starts delivering coffee.
or
)
Please note!
3. As soon as the wanted amount of coffee in cup is reached,
release the button: delivery stops.
The machine is now re-programmed according to the new
amount.
•
•
For a hotter cappuccino, it is advised to press the CLEAN
button to heat the ducts of the milk frother device (see
successive paragraph).
To prepare the cappuccino or the latte macchiato, the
appliance performs 2 deliveries: first the milk and
subsequently the coffee. If you would like to interrupt the
delivery in progress, press the previously pressed button.
Once delivery is completed, if wanting to increase the
amount of milk or coffee inside the cup, keep the button
(within a few seconds) relative to the preparation in
progress pressed.
Warmer cup (fig. 32)
The warmer cup can be switched on by pushing the
but-
ton: leave the cups on the appliance as long as they are warm.
This is useful to have warmer coffee.
•
•
Important!
When the appliance turns to low power function or stand-by
the cup warmer is still on until you don’t press the button to
switch it off. Pay attention not to touch it as it is hot.
Do not leave the milk container out of the refrigerator for
too long: the higher the milk temperature (41° F / 5°C is
ideal), the poorer the quality of the froth.
How to prepare milk-based drinks
To avoid milk with poor froth or large bubbles, always clean the
lid of the milk and the hot water nozzle as described in the“cle-
aning the milk container”at page 13.
1. Remove the lid (fig. 17);
2. Fill the milk container with sufficient amount of milk, not
Cleaning the milk frother device using the CLEAN button
After every use of the milk functions, perform cleaning to
eliminate the milk residues as follows:
1. Leavethemilkcontainerinsertedinthemachine(itisnot
necessary to empty the milk container);
11
Instructions for use
en
2. Place a cup or other container under the milk spout tube.
3. Keep the “CLEAN” button (fig. 25) pressed: lights
2. Keep the
button pressed.
3. When the hot water in the cup reaches the required level,
release the button. Programming is confirmed by the
lights flashing for three seconds.
The machine is now re-programmed according to the new
amount.
and
flash. When the lights stop flashing and the
appliance goes back to ready for use, release the “CLEAN”
button: the steam cleans the circuits inside the milk
frother.
Program the amount of coffee and milk in the cup for
cappuccino or milk
The machine has been set by default to deliver standard amounts
of coffee and milk. If you would like to amend these quantities,
proceed as follows:
1. Place a cup under the coffee spouts and the milk spout
tube.
2. Press the button relative to the preparation with milk to
be programmed and keep it pressed. After a few seconds,
the machine starts delivering the milk.
Delivering steam
1. Check the hot water spout is correctly attached (fig. 8).
2. Fill a container with the liquid to be heated/frothed and
immerse the water/steam spout into the liquid.
3. Press twice the
button(B7):therelativelightflashes
and the appliance starts steam delivery.
4. When the required temperature is obtained, interrupt
steam delivery by pressing the button again. (You should
not discharge steam for more than 3 minutes at a time).
3. Once the required quantity of milk has been delivered into
the cup, release the button; milk delivery stops.
4. Program the amount of coffee into the cup as for the
amount of milk.
5. Programming is confirmed by the lights flashing for 3
seconds.
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Cleaning the water spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
The machine is now re-programmed according to the new
amounts of milk and coffee.
1. Place a container under the cappuccino maker and press
the
button to deliver a little water (fig. 3).
Preparing the hot water and steam
Stop the flow of water by pressing the
again.
button
Scalding hazard!
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout.
3. Check the hole is not blocked. If necessary, clean with a
pin.
4. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
Do not leave the machine unattended when delivering hot
water. The spout heats up during delivery, therefore, only the
black part must be held.
Delivering hot water
1. Check the hot water spout is correctly attached (fig. 8).
2. Place a cup under the spout (as near as possible to avoid
sprays).
5. Reinsert the water spout.
3. Press the
button (B7): the relative light flashes and
Cleaning
the appliance starts hot water delivery.
4. The machine automatically stops delivery.
Attention!
•
•
Do not use solvents, abrasive detergents or alcohol to
clean the machine.
Only the milk container (D) can be washed in the dish
washer. No other part of the appliance can be washed in
the dishwasher.
Do not use metal objects to remove coffee deposits or
fouling as they might scratch the metal or plastic surfaces.
Please note!
To manually interrupt the hot water delivery, press
button again.
•
Programming the amount of water automatically
delivered
If you would like to amend the amount of water set by default,
proceed as follows:
•
1. Place a cup under the water spout.
12
Instructions for use
Descaling
en
Cleaning the drip tray
Descale the machine when the light
control panel. Proceed as follows:
flashes on the
Attention!
The drip tray is equipped with a floating water level indicator
(red) (A11). As soon as this indicator starts protruding from
the cup tray, empty the tray and clean it, otherwise the water
may overflow and damage the machine, and the surrounding
work-top.
1. Remove the water filter. Fill the tank with the descaling
solution obtained by diluting the descaler with water as
indicated on the descaler pack.
2. Insert the hot water spout (fig. 8).
3. Place one container under the boiler outlet and one under
the hot water spout (fig. 31) and ensure the drip tray is
empty and correctly inserted.
1. Remove the drip tray (fig. 26).
2.
Remove the cup tray, dispose of the water (fig. 27) and
clean the tray using a cloth: then re-assemble the drip tray.
3. Re-insert the drip tray.
4. Simultaneously press the
turns on (if the hot water spout has not been
inserted, the light flashes).
5. Press the button. Descaling is signaled by the
and
buttons: light
Cleaning the coffee filters
Regularly clean the coffee filters rinsing them under running
water. Check that the holes are not blocked. If they are, clean
them using a pin (fig. 28).
LED that alternate in sequence. The descaling program
automatically performs a series of deliveries from the
boiler outlet and from the hot water spout at intervals, to
remove the lime scale from inside the coffee machine.
Cleaning the boiler outlet
Rinsetheboileroutletevery200coffeesdelivered,bydelivering
0.5l of water from the boiler outlet (place a cup under the
boiler outlet and then press either the 1 or 2 cup coffee button
to deliver a coffee without using coffee powder).
6. Once the descaling solution is terminated, the light
turns on to indicate rinsing is necessary.
7. To eliminate the solution and lime scale residues, rinse the
tankandfillitwithfreshwater(withoutdescaler);empty
the containers and place them under the boiler outlet and
hot water spout.
Cleaning the milk container
Clean the milk container after each milk preparation, as
described below:
8. Press the
sequence.
button: rinsing starts and all LEDs flash in
1. Extract the lid.
2. Remove the milk spout tube and the intake tube (fig. 29).
3. Remove the froth regulator by by pulling it out (fig. 30).
4. Carefully clean all components using hot water and a mild
detergent. All components can be washed in the
dishwasher by positioning them on the upper rack
of the dishwasher. Pay particular attention that milk
residues do not remain inside the holes and in the groove
on the narrow part of the froth regulator.
9. Rinsing stops when the tank is empty: rinse and refill the
tank.
10. Light
turns on: press the relative button: delivery
starts and interrupts automatically.
The appliance is now ready for use.
Repairs to the coffee machine relative to lime scale problems
are not covered by the warranty if the descaling procedure
described above is not performed on a regular basis.
5. Also check that the intake tube and the milk spout tube
are not obstructed by milk residues.
6. Re-assemble the froth regulator, the milk spout tube and
the milk intake tube.
7. Place the lid on the milk container.
Replacing the filter
After two months of duration (see calendar), or if the appliance is
not used for 3 weeks, replace the filter as described in paragraph
“Activation of the softener filter and filling of the tank”(page 9).
13
Troubleshooting
Problem
Possible causes
Solution
The device will not switch on
The power supply cable is not inserted
correctly
Check that the power supply cable
connector is fully inserted in the
appropriate socket on the back of the
device; then check that the plug is
correctly connected to the power outlet
Espresso coffee does not flow out
No water in the tank
Fill the water tank
The holes in the filter-holder are blocked Clean the holes in the filter-holder spouts
The espresso boiler outlet is blocked
Clean as indicated in the “Cleaning the
boiler outlet”paragraph (page 13)
Espresso coffee drips from the edges of
the filter-holder instead of through the
holes
The filter-holder is not correctly inserted Attach the filter-holder correctly and
or is dirty
handle to the right until aligned to the
CLOSE position
The espresso boiler gasket has lost
elasticity or it is dirty
Have the espresso boiler gasket replaced
at a service center
The holes in the filter-holder spout are
Clean the holes in the filter holder spouts
blocked
The filter-holder does not hook onto the Too much coffee was poured in the filter Use the measure provided and make sure
device
to use the correct filter for the type of
preparation desired.
Loud pump noise
The water tank is empty
Fill the tank
The tank is inserted incorrectly and the
valve on the bottom is not open
Press the tank lightly to open the valve on
the bottom
The coffee cream is clear (it flows quickly The ground coffee has not been
Increase pressing of the ground coffee
from the spout)
sufficiently pressed
Not enough ground coffee
Increase the amount of ground coffee
The coffee is not ground finely enough
Only use coffee ground specifically for
espresso coffee machines
Incorrect type of ground coffee
Change the quality of the ground coffee
After coffee delivery, the coffee filter re-
Insert the filter-holder again, then
mains attached to the boiler outlet
remove it.
After the coffee has been prepared, the
pod or coffee powder remains attached to
the boiler outlet
Re-insert the filter-holder, deliver coffee,
remove the filter-holder.
14
Troubleshooting
en
Problem
Possible causes
Solution
The coffee cream is dark (it flows slowly The ground coffee is too tightly pressed
Press the coffee less
from the spout)
Large amount of ground coffee
Decrease the amount of ground coffee
The espresso boiler outlet is blocked
Perform cleaning as indicated in the section
“cleaning the boiler outlet” (page 13)
The filter is blocked
Perform cleaning as indicated in in the
section“cleaning the filter”(page 13)
The coffee is too finely ground
The ground coffee is too fine or is damp
Only use coffee ground specifically for
espresso coffee machines
Only use coffee ground specifically for
espresso coffee machines and it must not
be too damp
Incorrect type of ground coffee
Change the quality of the ground coffee
powder
The milk does not froth when The milk is not cold enough
making a cappuccino
Always use milk at refrigerator temperature
The cursor of the milk frother lid is not in Ensure the cursor is in the froth position
correct position
The milk container lid is dirty
Clean the milk lid as described in the
section “Cleaning the milk container”
(page 13)
The milk contains large
bubbles and there is little
froth .
The spout is dirty.
Clean as described in the section
“Cleaning the spout after use”.
The machine does not deliver any drink
No water in the tank
Fill the water tank
and the lights
a few seconds.
and
flash for
The tank is inserted incorrectly and the
valve on the bottom is not open
Press the tank lightly to open the valve on
the bottom
Incorrectly installed water filter
Activate the filter by following the
indicated procedure
The ground coffee is too tightly pressed
The espresso boiler outlet is blocked
Press the coffee less
Perform cleaning as indicated in the
section “cleaning the boiler outlet”
(page13)
The filter is blocked
Perform cleaning as indicated in the
section“cleaning the coffee filters”
The machine does not work and all lights
flash
Immediately disconnect the appliance
and contact an authorized service center
15
|